V3 Hardware Overview

To begin, the two major components of the NT8 are the head and deck. Both are located at the front of the NT8 instrument. The head primarily contains tools to aspirate and dispense liquids, and the deck contains plates, tip caddies, the protein source, and the wash and waste stations.

The NT8 V3 Hardware - Front View

The NT8 V3 Hardware - Front View

The NT8 Deck

Located at the front of the instrument, the NT8 deck contains everything needed for your dispenses including the plates, protein source, and tips.

The NT8 Deck

The NT8 Deck

The NT8 deck is divided into the following stations:

Note

Please refer to the NT8 hardware picture above to see the position of each station.

1 Waste Station

The waste station is where the NT8 disposes of low volume (LV) tips.

2 OPTIONAL: LCP Mixing Station

This option is only available if you purchase NT8 with the LCP option. The LCP Mixing Station saves you time from manually mixing lipids and protein solution. Syringes are installed on the mixing station and the plungers will move from side to side until the liquid is homogenous. The mixing speed is also adjustable to meet your needs. Please read Preparing LCP Samples for detailed instructions.

3 OPTIONAL: LCP Calibration Station

NT8 with an LCP Option includes a Calibration Station for your LCP syringe. The calibration process is fully automatic and should be done after you mount the syringe on the NT8 head. Read Attaching The LCP Syringe for more information.

4 Protein Source Station

The protein source station stores protein sample before it is dispensed into a plate. It is included in the NT8 accessories kit. The NT8 supports both low volume (LV) and high volume (HV) protein blocks, both of which come with a sensor that helps the NT8 Control Software to automatically detect the type of protein block being installed in the hardware.

Protein Block

Protein Block

When you purchase NT8, two protein blocks (low volume and high volume) come prepackaged in the accessories kit. Each protein block has three columns of eight drops each (24 total). The low volume protein block is capable of holding 3 μL while high volume protein block is capable of holding 13 μL. The protein sample is stored inside a disposable protein tray that is placed on top of the protein block and is secured by a magnet clamp.

5 Wash Station

The Wash Station is used to wash low volume pipette tips, allowing you to reuse them and reduce environmental waste. You can define the wash duration to meet your needs too!

6 Low Volume (LV) Tip Caddy Station

The Low Volume (LV) tip caddy station is a repository that holds up to 384 replacement LV tips. Use these tips to aspirate protein sample from the protein tray.

7, 8, 9 Protein Stations

On the NT8 deck, there are designated areas for three SBS footprint microplates. Three microplates can be placed on the deck to transfer reagents from one plate to another. A hanging drop cover sheet can be placed on station #1 for setting hanging drops.

The NT8 accessories kit also includes a reference plate, which is useful for tuning plate station 1, 2, and 3 to get accurate dispense locations. The reference plate has four crosshairs (indicated by orange circles in the picture below) in every corner for reference points. The crosshair that is located near the A1 symbol represents well A1 on a microplate.

Note

The reference plate can also be used as a medium to attach the LCP plate and cover sheet necessary for LCP and hanging drop experiments.

Reference Plate

Reference Plate

10 OPTIONAL: High Volume (HV) Tip Caddy Station

The HV tip caddy station presents in the NT8 deck if you purchase NT8 with this option. The HV Tip Caddy Station holds up to 96 replacement HV tips for the system.

11 OPTIONAL: Deep Well Station

The deep-well station is compatible with 96 deep-well plates, which are used to copies of your experiments.

The NT8 Head

The NT8 head contains tools for aspirating and dispensing liquids stored in the plates or trays on the NT8 deck. You can tell the NT8 to move the head forward and backward, up and down, or to the right or left.

What you can find on the NT8 head:

  • Low Volume (LV) Tip Attachments

    Located in the bottom-left corner of the NT8’s head, LV tip attachments are where you install the LV tips for use in aspiration and dispense. There are up to 8 tip attachments (known as flexible fingers), that can travel independently +/- 0.5 mm vertically. This ensures pipette tips to contour to uneven plate surfaces.

    All tips are also equipped with a sensor that indicates when a tip touches the surface, allowing the NT8 to drive down the surface of plate carefully. The tips will retract slightly away from the surface, allowing for a perfect dispense gap to set drops. This way, bubbles are eliminated and drop precision is improved.

    Note

    If the tip is touching a surface, the sensor will be off; otherwise it will be bright blue, as seen in the picture below.

    Low Volume (LV) Tips Attachments

    Low Volume (LV) Tips Attachments

    Note

    When you see a tip number referenced in the text, 1 is the tip closest to the back of the instrument and 8 is the one closest to the front.

  • OPTIONAL: High Volume (HV) Tip Attachments

    HV tip attachments are located in the bottom-right corner of the NT8’s head and are used for plate copy experiment. Each HV tip attachment is equipped with a sensor that detects contact with the liquid surface in a deep well plate. The HV tip attachment uses 200 μL pipette tips (eight at a time) to aspirate liquid from a deep well block and transfer it to a crystallization plate.

    High Volume (HV) Tip Attachments

    High Volume (HV) Tip Attachments

  • OPTIONAL: Lipidic Cubic Phase (LCP) Syringe Mount

    If your NT8 includes the LCP option, there is an LCP Syringe Mount on the front left side of the NT8 head. It is compatible with a Hamilton LCP syringe.

    LCP Syringe Mount

    LCP Syringe Mount

  • OPTIONAL: Lipidic Cubic Phase (LCP) Lever

    Adjust the LCP Syringe Mount.

    LCP Lever

    LCP Lever

    Note

    You can adjust the lever speed and height to fit the LCP syringe by clicking the Setup Joystick Speed button in the LCP Syringe Control panel and moving the lever button on the NT8’s head up and down, as needed.

Related Topics